How to Measure a 3D Model on Your Phone (STL, 3MF, OBJ)
Also in:DeutschEspañolFrançaisPortuguês日本語Türkçe

To measure a 3D model on your phone, open it in a viewer with a measure tool, tap two points, and read the distance in millimetres. Snap to corners, edges and centres for steady readings, and cut a section to measure walls and holes inside the part. Check the overall width, depth and height first: if they look 25.4 times too small, the file was exported in inches. Everything runs offline; the file is not uploaded.
You found the perfect bracket, but will an M3 screw go through the hole? Is the wall thick enough to survive being screwed down? Does the slot fit the 18 mm board it is meant for? You can find out at the printer after two hours, or on your phone in thirty seconds.
I build Extrude, a 3D file viewer for phones, and measuring is the reason many people open a model on their phone at all. This guide shows how to get readings you can trust, and what to compare them with.
How do you measure a 3D model on your phone?
- Open the model. STL, 3MF and OBJ all work. Read the overall dimensions first; they tell you if the scale is sane.
- Open the measure tool. In Extrude, tap Measure and analyse, then Measure distance.
- Tap the first point, then the second. The distance appears in millimetres.
- Let it snap. Points jump to a nearby corner, edge, midpoint, centre or face centre, so a fingertip does not have to be precise. Hold to aim, and hold a placed point to move it.
- Clear and measure again from another angle if a reading surprises you.
How do you measure a hole?
Turn the model until you look straight into the hole, then measure across it from one edge to the opposite edge. Compare the reading with the fastener:
| Screw | Typical clearance hole |
|---|---|
| M2 | 2.2 – 2.4 mm |
| M3 | 3.2 – 3.4 mm |
| M4 | 4.3 – 4.5 mm |
| M5 | 5.3 – 5.5 mm |
These are the fine and medium clearance sizes from the ISO 273 series. Printed holes often come out a little smaller than designed, especially small vertical ones, so a hole at the bottom of the range may need drilling out or a tiny scale tweak in the CAD file.
How do you measure a wall or the inside of a part?
Walls and internal features hide behind the outer surface. Cut through them:
- Open Section view from the same tools menu.
- Move the cut position until the plane passes through the wall or hole you care about. Flip shows the other side.
- Measure across the cut face. Section corners snap too, so wall thickness is two taps.
As a rule of thumb for FDM, walls thinner than about two nozzle widths (0.8 mm with a 0.4 mm nozzle) print weak or get skipped by the slicer.
Myth: “Phone measurements are too rough to be useful”
The measurement is not done by your eyes or your finger. It is calculated from the coordinates stored in the file, so it is as exact as the model itself. Your finger only picks which two points to use, and snapping places them on the exact corner, edge or centre. The usual cause of a “wrong” reading is a wrong unit: STL has no unit, so an inch export measures 25.4 times too small. Check the overall size first, and the rest follows.
What should you measure before printing?
- Overall size against your printer’s build volume.
- Holes against the screws, magnets or inserts you have.
- Slots and pegs against the part they must fit, leaving about 0.2 to 0.3 mm clearance for a sliding fit on most FDM printers.
- Thin walls and tabs, which break first.
Extrude (listed as STL Viewer on the App Store and Google Play) does all of this offline on iPhone and Android, for STL, 3MF and OBJ, and never uploads the file. If the model came by chat, here is how to open it from WhatsApp. On a computer, the browser STL viewer shows the overall size without installing anything.
Questions
Can I measure an STL file on my phone?
Yes. A 3D viewer with a measure tool lets you tap two points on the model and read the distance in millimetres. Extrude (listed as STL Viewer on the App Store and Google Play) does it offline for STL, 3MF and OBJ.
How do I measure a hole in an STL?
Turn the model so you look straight into the hole, then tap two points on opposite edges. Snapping to edges makes the reading steadier. Compare it with the screw: an M3 screw needs a clearance hole of about 3.2 to 3.4 mm.
How do I measure wall thickness in a 3D model?
Cut a section through the wall so you can see its cross-section, then measure from the outer face to the inner face. Walls thinner than about two nozzle widths often print weak or not at all.
Why does my measurement look wrong?
Check the unit first. STL has no unit, so a model exported in inches reads 25.4 times too small. Also make sure both points landed on the faces you meant; snapping to a corner or edge helps.
Do I need to upload the file to measure it?
No. A local viewer reads the file on your phone. Extrude never uploads models, and it works in flight mode.

