Why Your STL Prints Tiny (or Huge): the 25.4 Rule
Also in:DeutschEspañolFrançaisPortuguês日本語Türkçe

If your STL printed tiny, it was almost certainly exported in inches. STL files store bare numbers with no unit, and slicers read them as millimetres, so an inch model comes out 25.4 times too small. Scale it by 2540% in your slicer, or re-export it in millimetres. Ten times too small means centimetres; a thousand times means metres. Check the size before you print: a phone viewer shows it in millimetres in seconds.
You download a phone stand, hit print and walk away. Three hours later there is a grey crumb in the middle of the bed. Nothing jammed and nothing warped, and the printer did exactly what the file said. That is the frustrating part: the machine worked, and you still lost an afternoon and a few metres of filament to a part you cannot use.
I build Extrude, a 3D file viewer that has opened more than 15,000 models on phones since September, and a wrong-size print is one of the oldest surprises in 3D printing. To show exactly what it looks like, I took our 20 mm calibration cube, saved it in inches, and opened it in our own web viewer: it read 0.79 × 0.79 × 0.79 mm. You can download that file and try it yourself.
Why does an STL print the wrong size?
Because the file does not know what unit it is in. An STL is a list of triangles, and each corner is just three numbers. The Library of Congress format description notes that STL carries no scale or unit information: the numbers are whatever the exporting program wrote.
Slicers have to pick a unit, and nearly all of them pick millimetres. When the designer worked in millimetres, everything lines up. When they worked in inches, a 79 mm stand is stored as about 3.11, and your slicer prints 3.11 mm.
How do you tell which unit it was?
Compare the size you see with the size the part should be, then look at the ratio.
| Size looks… | Likely exported in | Fix in the slicer |
|---|---|---|
| 25.4× too small | inches | scale 2540% |
| 10× too small | centimetres | scale 1000% |
| 1000× too small | metres (common from Blender) | scale 100000% |
| 25.4× too big | a millimetre model read as inches | scale 3.937% |
A phone stand that should be about 80 mm wide and shows as 3.1 mm is an inch file. A miniature that should be 30 mm and shows 3 mm was exported in centimetres. OBJ files have the same blind spot, so the same table applies to an OBJ model that opens at an odd size.
What if it prints 25.4× too big?
That is the same mistake in reverse: a model drawn in millimetres was read as inches, usually because a slicer or CAD import setting was switched to inches. A 20 mm cube suddenly claims to be 508 mm and will not fit the bed. Scale it by 3.937% (one divided by 25.4), or switch the import unit back to millimetres and open it again.
How do you fix it?
- Scale uniformly by the factor. In any slicer, select the model and set the scale to the percentage in the table, with the axes locked so all three sides grow together. Then read the new size back: it should match what the designer intended to within a fraction of a millimetre.
- Use the slicer’s helper if it offers one. PrusaSlicer asks whether a very small model was defined in inches and offers to convert it, and Cura has a preference that scales extremely small models up when they are opened. Both are guesses based on how small the part looks, so check the result.
- Fix it at the source. If you made the model, set the export unit to millimetres in your CAD tool and export again, and it will open at the right size in every slicer and viewer from then on.
- Send 3MF instead. A 3MF file stores its unit inside the file (the 3MF core specification defines a unit attribute), so it cannot be misread this way.
Myth: “The slicer shrank my model”
It did not. The slicer read the numbers it was given. Scale the 0.79 mm test cube by 2540% and it is exactly 20 mm again (0.7874 × 25.4 = 20.00), because nothing was lost on the way, only the unit was wrong. That is the quick test for any tiny model: if one of the factors in the table gives you a sensible, round size, you have found the unit. If none of them does, the model was probably drawn at the wrong size to begin with, and it is worth asking the designer before you print it.
How do you check the size before printing?
Open the file and read its size in millimetres before you slice. On a computer your slicer shows it. On a phone, when a file arrives on WhatsApp or by email, a viewer does the same job.
In the Extrude app (listed as STL Viewer on the App Store and Google Play) the model opens in 3D with its width, depth and height in millimetres, and you can tap two points to measure a hole or a wall. It works offline, and the file never leaves your phone. If you are on an iPhone, our guide on opening STL files on iPhone walks through it from Files, Mail and WhatsApp.
Ten seconds of checking saves a three-hour print. If you are at a computer, the browser viewer shows the same size readout without installing anything, the file stays on your machine, and you can test it with the inch cube above to see exactly what a wrong unit looks like before it costs you a print.
Questions
Why did my STL print so small?
The file was almost certainly exported in inches. STL stores plain numbers with no unit, and slicers read them as millimetres, so an inch model comes out 25.4 times too small. Scale it by 2540% in your slicer, or re-export it in millimetres.
What unit does an STL file use?
None. The format has no field for units. By convention almost every slicer and CAD tool treats the numbers as millimetres, which is why a file exported in another unit prints at the wrong size.
How do I convert an STL from inches to millimetres?
Scale it uniformly by 25.4 (2540%). PrusaSlicer offers to convert when a model looks very small, and Cura can scale tiny models on import. The cleanest fix is to re-export from your CAD tool with the unit set to millimetres.
My STL is 10 times too small. What happened?
It was exported in centimetres. Scale by 10 (1000%). If it is 1000 times too small, it was exported in metres, which often happens with Blender files; scale by 1000 or set the export scale.
Can I check an STL's size on my phone?
Yes. A viewer such as Extrude (listed as STL Viewer on the App Store and Google Play) shows the model's size in millimetres and lets you measure between two points, offline and without uploading the file.

